Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Belgard Fence Installation: The Austin Owner’s Guide
Belgard fence installation in Austin typically runs $3,500 to $9,000 installed, depending on fence length, terrain, and whether we’re doing a fresh run or replacing panels on an existing line. We install Belgard fence systems to their exact installation specs and stand behind the work with a written 365-Day Done Right Promise. Most Austin owners call us after a storm catches the fence wrong, or after they notice posts leaning in a way that isn’t going to fix itself. By the time the gate drags or a panel starts humming in the wind, the underlying problem has usually been working on the fence for a while.
Which Belgard Fence Panels and Post Systems This Applies To
Belgard makes two main fence product families that we install and repair in Austin: the Belgard Elements fence line (modular stone-and-wood look, concrete posts with composite infill panels) and the Belgard U-Cara/Roman stack modular wall systems that homeowners sometimes run as low perimeter fencing. The compatibility gotcha that trips up most homeowners is post-to-panel spacing. Belgard Elements posts are set on 6-foot centers, and the panel slots are cut for a specific panel thickness. If someone swapped in a generic panel from a big-box store, the slot fit is wrong and wind rattle begins almost immediately. We identify the exact part by measuring the post face, the panel thickness, and checking the mold stamp on the back side of any concrete component. For replacement parts, we always recommend genuine Belgard components over aftermarket equivalents. The aftermarket stuff doesn’t match the color tone after a few Austin summers of UV and limestone dust exposure.
Styles & brands we work with
Signs Your Belgard Fence Installation Is Failing
- Posts leaning out of plumb. This usually means the concrete footing wasn’t deep enough when the fence went in, or water has been softening the soil around the base. In Austin’s clay-heavy soil, we see this a lot after extended dry spells followed by heavy rain.
- Gate dragging or not latching. The post has moved, or the hinge plate has worked loose inside the concrete post. On Belgard systems, the hinge hardware relies on the post staying dead vertical.
- Wind rattle from loose panels. The panel-to-post slot clearance has widened, which means either the panel shrank slightly or the slot was never shimmed correctly. Every summer thunderstorm will make it worse.
- Hairline cracks through the face of a concrete post. Freeze-thaw cycles are rare in Austin, but they do happen north of the river in places like Avery Ranch, and the thermal expansion from direct afternoon sun is enough to open a crack that starts from a bad pour.
- Discoloration that goes deeper than surface dust. Belgard uses color-infused concrete, so fading should be even. If you see patchy bleaching, someone attempted a seal, or the panel isn’t genuine Belgard and the dye lot didn’t hold.
See the difference
Before
After
Before
After
Before
AfterBelgard Fence Installation Cost in Austin & What’s Included
For a full Belgard fence installation in Austin, you’re looking at $3,500 to $9,000. On the low end, that’s a shorter run of replacement panels and posts using existing footings. On the high end, it’s a full perimeter with new footings, gate hardware, and terrain correction. Here’s how the cost breaks down.
- Parts and materials: $1,800 – $4,500 for genuine Belgard posts, panels, and hardware, with concrete and rebar included.
- Labor and installation: $1,200 – $3,500 depending on access, post removal, and how much of the old footing has to be dug out.
- Site prep and haul-away: $300 – $800 if old fence material needs to be cut out and disposed.
- Terrain and layout complexity: $200 – $700 for slope adjustments, tree-root work, or tight side-yard access.
Every quote we give is a written number before any work starts. The number on day one is the number on the invoice. And the installation itself carries our 365-Day Done Right Promise in writing: if the fence settles, cracks, or the gate drifts inside that year, we come back and fix it at no charge.
DIY or Call Us?
A homeowner can safely do a lot here: check post vertical with a level, look at the condition of the concrete around the post base, and inspect the gate latch strike for obvious misalignment. What a homeowner shouldn’t do is pull a Belgard post out of the ground and attempt to reset it solo. These posts are heavy and once they start tipping, they don’t forgive. The post is the structural anchor for the whole fence line, and a badly reset post just moves the problem a few months down the road. If your fence is leaning, cracking, or the gate doesn’t close against the strike plate, call us at (325) 225-5429. Trevor Nash will walk the fence with you, tell you what’s actually wrong, and put a number on it before we touch anything.
FAQs
A properly installed Belgard fence should last 20 to 25 years in the Austin climate. The concrete components are the strong point; the common failure point is the footing or the panel hardware, not the Belgard material itself. We also stock parts for other brand-name installs we do, like KraftMaid cabinetry and Cambria or Silestone countertops, but the Belgard system wear items are almost always footing- or hardware-related. Call (325) 225-5429 if your fence is under 10 years old and already failing; that’s a sign the original install was short-cut.
Frequently, yes. If the post is still structurally sound and the panel slots are intact, we can reset the post in a deeper footing, shim the panel, and bring the fence back to straight without replacing a single Belgard component. If the post itself is cracked through, that post needs to come out. We’ll tell you honestly which situation you’re in, and the repair always includes a written quote before work begins.
Most Belgard fence repairs are completed in a single day. A full installation of a typical Austin yard runs two to four days, depending on the length of the run and how much old concrete needs to be removed. We schedule a defined arrival window and show up in it; that’s part of the Kingswell Way.
We keep common Belgard panel shims, hinge kits, and post-mount hardware on the truck, and we can source full posts and panels through our normal Belgard supplier channel in a day or two. If we’re already on site and the job needs a specific post, we’ll get it ordered before we leave so the return trip is the finish trip. For anything involving a heavy post reset, we recommend letting our crew handle it. The weight and balance of these components can cause real injury if one tips while you’re working alone.
Written by Trevor Nash, Owner, Penhallow Remodeling Austin at Penhallow Remodeling Austin, serving Austin and nearby areas.
