Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Cambria Driveway & Pavers: The Austin Owner’s Guide
Cambria driveway and pavers in Austin typically run $7,000 – $18,000 installed for a full paver driveway, depending on square footage, base preparation, and the specific paver line. We stock Cambria-compatible pavers and hardscape materials, and our crews can usually start within a week or two of your written estimate. Most homeowners discover a problem the same way: a paver sinks or shifts after a heavy rain, or they notice surface spalling (flaking) after a few Texas summers.
If you’re standing in your driveway looking at a cracked paver or a low spot that wasn’t there last year, this page will tell you exactly what you’re dealing with, what it should cost to fix it right, and when it makes sense to call us at (325) 225-5429.
Which Cambria Models This Applies To
Cambria makes quartz countertops, not driveway pavers, so when we talk about Cambria driveways in Austin, we’re talking about Cambria-branded paver products in their hardscape line and the paver systems designed to integrate with Cambria’s outdoor surfaces. The most common lines we work with are the Cambria Estate Paver series (3-piece modular patterns) and the Cambria Bullnose Paver, which is cut with a rounded edge for driveway borders and steps.
Here’s the compatibility gotcha most people hit: Cambria pavers are sold in modular sets, not singles. That means if a section of your driveway was laid in a 3-piece pattern with square, rectangle, and half-square units mixed in, you can’t just replace one paver that cracked. You need the matching unit from the same manufacturing lot, or the color and dimensional tolerance will be off enough that the patch looks like a patch. We’ve seen homeowners order a “matching” paver online and end up with a 2mm height difference that leaves a lip every time they pull into the garage.
When you call us, here’s what we’ll ask you to check: look for a stamp or label on the underside of a loose paver, and measure the unit thickness with a tape measure (Cambria pavers typically run 60mm or 80mm). If you can’t find a stamp, send us a photo and we’ll identify the line from the surface texture and edge profile. Penhallow Remodeling Austin is an independent contractor, not a Cambria affiliate, but we work with their paver line regularly because the dimensional consistency is better than most of what you’ll find at a big-box store.
Styles & brands we work with
Signs Your Cambria Driveway & Pavers Is Failing
- Depressions or low spots that hold water after rain. This is almost always a base failure, not a paver failure. The compacted base under the pavers has eroded or settled, and the pavers are just following the ground down. Patching the surface won’t fix it; the base has to be rebuilt in that area.
- Pavers that rock or wobble when you step on them. The bedding sand layer has washed out or compacted unevenly. In Austin’s clay-heavy soils, we see this most often at driveway edges where water runs off and finds a path under the paver edge.
- Surface flaking or spalling on individual pavers. This is a material defect or freeze-thaw damage, though Austin’s freeze cycles are mild. More often it’s a manufacturing issue from a specific lot, which is partly why Cambria’s warranty paperwork matters if you have it.
- Wide or uneven joints between pavers. The interlocking bond has broken down, usually from vehicle weight pressing against a weak edge. Once joints spread beyond about a quarter inch, the pavers start working independently and the pattern degrades fast.
- Edge pavers collapsing along the driveway border. The edge restraint (usually plastic, aluminum, or concrete) has failed or was never installed. Without a solid edge, nothing else stays put.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full Cambria-compatible paver driveway replacement in Austin runs $7,000 – $18,000 installed. A partial repair, like rebuilding a sunken section or replacing a dozen damaged pavers, typically falls between $800 and $3,500 depending on how much base work is required and whether we need to haul out old material.
What drives the number: square footage is the biggest factor, but base condition matters just as much. Austin’s clay soil expands and contracts with moisture, and if the original base was skimped on (we see 2-3 inches of base where we’d put 6-8), the fix costs more because we’re rebuilding what should have been done right the first time. Paver thickness (60mm vs 80mm) changes material cost, and any border work or steps add to the total.
Every estimate you get from us is a written number, not a range you have to interpret. You’ll see the material line, the labor line, and the base prep line separately. And like every job we do in Austin, the work carries our 365-Day Done Right Promise: if something fails in the first year, we come back and fix it. No invoice, no argument.
DIY or Call Us?
You can safely check the obvious things yourself: whether the paver rocks underfoot, whether joints have spread, whether water pools in one spot. Those observations help us give you a faster, more accurate phone estimate. But pulling up pavers and rebuilding the base is not a weekend project. The base needs proper compaction (we use a plate compactor, not a hand tamper), the slope needs to move water away from your foundation, and the edge restraint has to be solid or the whole job fails again.
We’ve pulled up DIY paver repairs in Austin where the homeowner skipped the base work to save a few hundred dollars, and the pavers were shifting again inside six months. The honest answer: call us at (325) 225-5429 for a free estimate. We’ll give you a written number, show up when we say, and if the repair fails inside a year, the return visit is free.
FAQs
A properly installed paver driveway with a solid base will last 25 – 30 years in Austin’s climate before the pavers themselves need replacing, though the surface texture may show wear from tires and sun exposure after about 15 years. What fails earlier, usually, is the base beneath it, which is why we spend as much time on compaction and drainage as we do on the pavers themselves. Call (325) 225-5429 if you’d like us to look at your existing base before you spend money on new pavers.
Yes, in most cases we can pull the affected pavers, rebuild the base underneath, and reset them without replacing the whole driveway. Repairs run $800 – $3,500 depending on how many pavers are involved and how much base work is needed. If the pavers have spalled or cracked through, we’ll match them as closely as the available lots allow and talk you through what level of color match to expect.
A repair of a sunken section usually takes one to two days, including base rebuild and re-compaction. A full driveway replacement typically runs three to five working days in Austin, depending on size, demolition of the old surface, and whether we need to re-grade the base. You’ll get an arrival window in writing before we start, and we tell you if the schedule changes before you have to ask.
We stock the most common Cambria-compatible paver sizes and edge restraints on our trucks, along with bedding sand and base aggregates, so many repairs can be quoted and completed in the same trip for Austin homeowners. If your driveway uses a less common paver size or color, we’ll order it from our local Austin supplier before we schedule the work. We also keep parts and materials on hand for other major brands, including KraftMaid, Silestone, and Kohler, so if you have multiple projects in mind, we can scope the whole list at once.
Written by Trevor Nash, Owner, Penhallow Remodeling Austin at Penhallow Remodeling Austin, serving Austin and nearby areas.
